View SXX06XSX_8830917.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 SXX06XSX & sxx06x series description excellent unidirectional switches for phase control applications such as heating and motor speed controls. sensitive gate scrs are easily triggered with microamps of current as furnished by sense coils, proximity switches, and microprocessors. standard phase control scrs are triggered with few milliamperes of current at less than 1.5v potential. features & benefts ? rohs compliant ? glass C passivated junctions ? voltage capability up to 1000 v ? surge capability up to 100 a main features symbol value unit i t(rms) 6 a v drm /v rrm 400 to 1000 v i gt 0.2 to 15 ma schematic symbol agency approval agency agency file number l package: e71639 applications typical applications are capacitive discharge systems for strobe lights, nailers, staplers and gas engine ignition. also controls for power tools, home/brown goods and white goods appliances. internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. r ohs additional information datasheet samples resources teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 absolute maximum ratings standard scrs symbol parameter value unit i t(rms) rms on-state current sxx06l t c = 100c 6 a sxx06r sxx06d sxx06v t c = 110c i t(av) average on-state current sxx06l t c = 100c 3.8 a sxx06r sxx06d sxx06v t c = 110c i tsm peak non-repetitive surge current single half cycle; f = 50hz; t j (initial) = 25c 83 a single half cycle; f = 60hz; t j (initial) = 25c 100 i 2 t i 2 t value for fusing t p = 8.3 ms 41 a 2 s di/dt critical rate-of-rise of on-state current f = 60hz; t j =125c 100 a/s i gtm peak gate current t j = 125c 2 a p g(av) average gate power dissipation t j = 125c 0.5 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c note: xx = voltage absolute maximum ratings sensitive scrs symbol parameter test conditions value unit i t(rms) rms on-state current sxx06lsy t c = 80c 6 a sxx06rsy sxx06dsy sxx06vsy t c = 95c i t(av) average on-state current sxx06lsy t c = 80c 3.8 a sxx06rsy sxx06dsy sxx06vsy tc = 95c i tsm peak non-repetitive surge current single half cycle; f = 50hz; t j (initial) = 25c 83 a single half cycle; f = 60hz; t j (initial) = 25c 100 i 2 t i 2 t value for fusing t p = 8.3 ms 41 a 2 s di/dt critical rate of rise of on-state current f = 60hz; t j = 110c 100 a/s i gtm peak gate current t j = 110c 1 a p g(av) average gate power dissipation t j = 110c 0.1 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 110 c note: xx = voltage, y = sensitivity teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 electrical characteristics (t j = 25c, unless otherwise specifed) sensitive scrs symbol test conditions value unit sxx06xs2 sxx06xs3 i gt v d = 6v r l = 100 max. 200 500 a v gt v d = 6v r l = 100 max. 0.8 v dv/dt v d = v drm ; r gk = 1k?; t j = 110c typ. 8 v/s v gd v d = v drm r l = 3.3 k t j = 110c min. 0.2 v v grm i gr = 10a min. 6 v i h i t = 20ma (initial) max. 6 8 ma t q i t = 2a; t p = 50s; dv/dt=5v/s; di/dt=-30a/s max. 50 45 s t gt i g = 2 x i gt pw = 15s i t = 12a typ. 4 5 s note: xx = voltage, x = package electrical characteristics (t j = 25c, unless otherwise specifed) standard scrs symbol test conditions value unit sxx06x i gt v d = 12v r l = 60 max. 15 ma v gt v d = 12v r l = 60 max. 1. 5 v dv/dt v d = v drm ; gate open; t j = 100c 400v min. 350 v/s 600v 300 800v 250 1000v 100 v d = v drm ; gate open; t j = 125c 400v 250 600v 225 800v 200 v gd v d = v drm r l = 3.3 k t j = 125c min. 0.2 v i h i t = 200ma (initial) max. 30 ma t q i t = 2a; t p = 50s; dv/dt=5v/s; di/dt=-30a/s max. 35 s t gt i g = 2 x i gt pw = 15s i t = 12a typ. 2 s note: xx = voltage, x = package teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 static characteristics symbol test conditions value unit v tm i t = 12a; t p = 380 s max. 1. 6 v i drm / i rrm v drm = v rrm sxx06xyy t j = 25c 400 C 600v max. 5 a t j = 110c 400 C 600v 250 sxx06x t j = 25c 400 C 800v 10 1000v 20 t j = 100c 400 C 800v 200 1000v 3000 t j = 125c 400 C 800v 500 note: xx = voltage, x = package, yy = sensitivity thermal resistances symbol parameter value unit r (j-c) junction to case (ac) sxx06rsy 2.6 c/w sxx06lsy 4.3 sxx06vsy 2.4 sxx06dsy 1. 8 sxx06r 2.5 sxx06l 4.0 sxx06v 2.3 sxx06d 1. 7 r (j-a) junction to ambient sxx06rsy 40 c/w sxx06lsy 65 sxx06vsy 85 sxx06r 40 sxx06l 50 sxx06v 70 note: xx = voltage, y = sensitivity teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 figure 1: normalized dc gate trigger current vs. junction temperature (sensitive scr) figure 2: normalized dc gate trigger current vs. junction temperature (standard scr) 0.0 1. 0 2.0 3.0 4.0 junction t emper at ur e (t j ) - (oc) ratio of i gt /i gt (t j =25oc) -40 -1 5 10 35 60 85 11 0 0.0 1.0 2.0 3.0 4.0 junction t emper at ur e (t j ) - (oc) ratio of i gt / i gt (t j = 25oc) -40 -1 5 10 35 60 85 11 0 12 5 figure 5: on-state current vs. on-state voltage (typical) figure 6: power dissipation (typical) vs. rms on-state current 0 1 2 3 4 5 6 0 1 2 3 4 5 6 rms on-stat e cur r ent [i t(rms) ] - (amps) av er ag e on-stat e p ower dissipation [p d(a v) ] - (w at ts) 0.0 0.5 1.0 1.5 2.0 junction t emper at ur e (t j ) - (oc) ratio of v gt / v gt (t j = 25oc) -40 -1 5 10 35 60 85 11 0 12 5 figure 3: normalized dc gate trigger voltage vs. junction temperature figure 4: normalized dc holding current vs. junction temperature 0.0 0.5 1.0 1.5 2.0 junction t emper at ur e (t j ) - (oc) ratio of i h / i h (t j = 25oc) -40 -1 5 10 35 60 85 11 0 12 5 5 in st an ta ne ous on -s ta te cu rre nt (i t ) -amps 0 10 15 20 25 30 t j = 25 c 0. 7 0. 8 0. 9 in st an ta ne ous on -s ta te vo lt ag e (v t ) - volts 1. 0 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 figure 7: maximum allowable case temperature vs. rms on-state current figure 8: maximum allowable case temperature vs. average on-state current 80 85 90 95 10 0 10 5 11 0 11 5 12 0 12 5 13 0 4 3 2 1 0 sxx06l sx06ls y sxx06r sy sxx06ds y sxx06vs y sxx06r sxx06d sxx06v current wa veform: sinsuoidal lo ad: resistiv e or inductiv e conduction angle: 1 80 free air ra ting av er ag e on-stat e cur r ent [i t(av e) ] - amps maximum allowable case t emper at ur e (t c ) - oc 80 85 90 95 100 105 110 115 120 125 130 sxx06r sxx06d sxx06v 0 1 2 3 4 5 6 7 current wa veform: sinsuoidal lo ad: resistiv e or inductiv e conduction angle: 1 80 free air ra ting sxx06l rms on-stat e cur r ent [i t(rms) ] - amps maximum all owa ble case t emper at ur e (t c ) - o c sxx06lsy sxx06rsy sxx06dsy figure 9: maximum allowable ambient temperature vs. rms on-state current 0 20 40 60 80 100 120 0.0 0.5 1.0 1.5 2.0 2.5 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 free air rating sxx06v sxx06rsy sxx06lsy sxx06vsy sxx06l sxx06r rms on-stat e cur r ent [i t(rms) ] - amps maximum allowable t emper at ur e (t a ) - oc figure 10: maximum allowable ambient temperature vs. average on-state current 0 20 40 60 80 100 120 5 . 1 0 . 1 5 . 0 0 . 0 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 free air rating sxx06rsy sxx06lsy sxx06r sxx06l sxx06v sxx06vsy av er ag e on-stat e cur r ent [i t(av e) ] - amps maximum allowable ambient t emper at ur e (t a ) - oc note: xx = voltage, y = sensitivity figure 11: peak capacitor discharge current 10 10 0 1 000 0 . 0 5 0 . 10 5 . 0 pulse cur r ent dur ation (t w ) - ms pe ak disc ha rg e cu rr ent (i tm ) - amp s i trm t w 1. 0 figure 12: peak capacitor discharge current derating 0.0 0.2 0.4 0.6 0.8 1. 0 1. 2 0 2 5 50 75 10 0 1 25 15 0 nor maliz ed p eak cur r ent sensitiv e scr case t emper at ur e (t c ) - oc standar d scr teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 1 10 10 0 sur ge cur r ent dur ation -- f ull cy cles p eak sur ge (non-r epetitiv e) on-stat e cur r ent (i tsm ) ? amps 1 10 10 0 10 00 figure 13: surge peak on-state current vs. number of cycles supply frequency: 60 hz sinusoidal load: resistive rms on-state current: [i t(rms) ]: maximum rated value at specifed case temperature notes: 1. gate control may be lost during and immediately following surge current interval. 2. overload may not be repeated until junction temperature has returned to steady-state rated value. soldering parameters refow condition pb C free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) 60 C 180 secs average ramp up rate (liquidus temp) (t l ) to peak 5c/second max t s(max) to t l - ramp-up rate 5c/second max refow - temperature (t l ) (liquidus) 217c - temperature (t l ) 60 C 150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20 C 40 seconds ramp-down rate 5c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 280c ti me te mperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p r e h eat ramp-up ramp-up ramp-down r am p - do teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 physical specifcations environmental specifcations test specifcations and conditions ac blocking mil-std-750, m-1040, cond a applied peak ac voltage @ 125c for 1008 hours temperature cycling mil-std-750, m-1051, 100 cycles; -40c to +150c; 15-min dwell-time temperature/ humidity eia / jedec, jesd22-a101 1008 hours; 320v - dc: 85c; 85% rel humidity high temp storage mil-std-750, m-1031, 1008 hours; 150c low-temp storage 1008 hours; -40c resistance to solder heat mil-std-750 method 2031 solderability ansi/j-std-002, category 3, test a lead bend mil-std-750, m-2036 cond e terminal finish 100% matte tin-plated body material ul recognized epoxy meeting fammability classifcation 94v-0 lead material copper alloy design considerations careful selection of the correct device for the applications operating parameters and environment will go a long way toward extending the operating life of the thyristor. good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. correct mounting, soldering, and forming of the leads also help protect against component damage. product selector part number voltage gate sensitivity type package 400v 600v 800v 1000v sxx06rs2 x x 0.2ma sensitive scr to-220r sxx06ls2 x x 0.2ma sensitive scr to-220l sxx06vs2 x x 0.2ma sensitive scr to-251 sxx06ds2 x x 0.2ma sensitive scr to-252 sxx06rs3 x x 0.5ma sensitive scr to-220r sxx06ls3 x x 0.5ma sensitive scr to-220l sxx06vs3 x x 0.5ma sensitive scr to-251 sxx06ds3 x x 0.5ma sensitive scr to-252 sxx06r x x x x 15ma standard scr to-220r sxx06l x x x x 15ma standard scr to-220l sxx06v x x x x 15ma standard scr to-251 sxx06d x x x x 15ma standard scr to-252 note: xx = voltage teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 dimensions to-251aa (v/i-package) v/i-pak through hole dimension inches millimeters min typ max min typ max a 0.037 0.040 0.043 0.94 1. 01 1.09 b 0.235 0.242 0.245 5.97 6.15 6.22 c 0.350 0.361 0.375 8.89 9.18 9.53 d 0.205 0.208 0.213 5.21 5.29 5.41 e 0.255 0.262 0.265 6.48 6.66 6.73 f 0.027 0.031 0.033 0.69 0.80 0.84 g 0.087 0.090 0.093 2.21 2.28 2.36 h 0.085 0.092 0.095 2.16 2.34 2.41 i 0.176 0.180 0.184 4.47 4.57 4.67 j 0.018 0.020 0.023 0.46 0.51 0.58 k 0.035 0.037 0.039 0.90 0.95 1. 0 0 l 0.018 0.020 0.023 0.46 0.52 0.58 p 0.042 0.047 0.052 1.06 1.20 1.32 q 0.034 0.039 0.044 0.86 1. 0 0 1. 11 r 0.034 0.039 0.044 0.86 1. 0 0 1. 11 s 0.074 0.079 0.084 1.86 2.00 2.11 area: 0.040 in 2 t c mea suring poin t ga te g i e d a b c f j h k l 5.28 .208 5.34 .21 0 anode cathode anode p q r s dimensions to-252aa (d-package) d-pak surface mount dimension inches millimeters min ty p max min ty p max a 0.037 0.040 0.043 0.94 1. 01 1.09 b 0.235 0.243 0.245 5.97 6.16 6.22 c 0.106 0.108 0.113 2.69 2.74 2.87 d 0.205 0.208 0.213 5.21 5.29 5.41 e 0.255 0.262 0.265 6.48 6.65 6.73 f 0.027 0.031 0.033 0.69 0.80 0.84 g 0.087 0.090 0.093 2.21 2.28 2.36 h 0.085 0.092 0.095 2.16 2.33 2.41 i 0.176 0.179 0.184 4.47 4.55 4.67 j 0.018 0.020 0.023 0.46 0.51 0.58 k 0.035 0.037 0.039 0.90 0.95 1. 0 0 l 0.018 0.020 0.023 0.46 0.51 0.58 m 0.000 0.000 0.004 0.00 0.00 0.10 n 0.021 0.026 0.027 0.53 0.67 0.69 o 0 0 5 0 0 5 p 0.042 0.047 0.052 1.06 1.20 1.32 q 0.034 0.039 0.044 0.86 1. 0 0 1. 11 m o n h j l k .1 18 3 .063 1 .60 .071 1 .80 .264 6.71 .264 6.71 .1 81 4.60 ga te anode cathode anode t c mea suring poin t g i d e a b c f 5.28 .208 5.34 .21 0 : 0.040 in 2 area p q teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 dimensions to-220ab (r-package) non-isolated mounting tab common with center lead dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 g 0.540 0.575 13.72 14.61 h 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 k 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1. 14 1.52 r 0.038 0.048 0.97 1.22 k j a h g b f e c d l r t c mea suring poin t anode o p n m .27 6 7. 01 .526 1 3.36 .320 8.1 3 area (ref .) 0.1 7 in 2 no tch in ga te lead to id. non-isola ted ta b ga te ca thode anode dimensions to-220ab (l-package) isolated mounting tab dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 g 0.540 0.575 13.72 14.61 h 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 k 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1. 14 1.52 r 0.038 0.048 0.97 1.22 a h g b f e c d l r t c mea suring poin t area (ref .) 0.1 7 in 2 o p n m .320 8.1 3 .526 1 3.36 .27 6 7. 01 k j ga te ca thode anode note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). teccor ? brand thyristors 6 amp sensitive & standard scrs
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 05/02/16 packing options part number marking weight packing mode base quantity sxx06l/ryytp sxx06l/ryy 2.2 g tube 500 (50 per tube) sxx06dyytp sxx06dyy 0.3 g tube 750 (75 per tube) sxx06dyyrp sxx06dyy 0.3 g embossed carrier 2500 sxx06vyytp sxx06vyy 0.4 g tube 750 (75 per tube) sxx06l/rtp sxx06l/r 2.2 g tube 500 (50 per tube) sxx06dtp sxx06d 0.3 g tube 750 (75 per tube) sxx06drp sxx06d 0.3 g embossed carrier 2500 sxx06vtp sxx06v 0.4 g tube 750 (75 per tube) note: xx = voltage; yy = sensitivity 0.51 2 (1 3.0) arbor hole diameter dc xxxxxx xxxxxx dc xxxxxx dc xxxxxx xx gate cathode anode 0.63 (1 6.0) 0.1 57 (4.0) 0.64 (1 6.3) 1 2.99 (330.0) 0.524 (1 3.3) 0.31 5 (8.0) 0.059 dia (1 .5) * * co ver tape xx xx direction of f eed dimensions are in inc hes (and millimeter s). to-252 embossed carrier reel pack (rp) specs meets all eia-481-2 standards part numbering system part marking system s 60 06 l s2 56 device type s: scr voltage ratin g 40: 400v 60: 600v 80: 800v k0: 1000 v current ratin g 06: 6a sensitivity & type sensitive scr: s2: 200a s3: 500a standard scr: (blank): 15ma package type l: to-220 isolated r: to-220 non-isolated v: to-251 (v/i-pak ) d: to-252 (d-pak ) lead form dimensions xx: lead form option s6006ds2 ymldd ? to-252aa- (d package ) to-251aa- (v package) date code marking y:year code m: month code l: location code dd: calendar code s6006ds2 ymldd ? to-252aa ? (d package ) to-251aa ?( v package) s6006f 1 y xxxx to-202 ty pe 1 (f package) s6006ds2 ymldd ? ? ? m y s6006rs2 to -220 ab - (l and r pa ck age) date code marking y:year code m: month code xxx: lot trace code teccor ? brand thyristors 6 amp sensitive & standard scrs

▲Up To Search▲

Price & Availability of SXX06XSX

	To Download SXX06XSX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .